WBPA1016A: 1.0-1.6 GHz 2.0 Watt Broadband Power Amplifier. Company advantage inventory.

Main features

?50 ohm impedance

?1.0?1.6 GHz

?2.6 dB noise figure

?45.0 dBm output IP3

?27.0 dB gain

?+/- 0.5 dB gain flatness

?33.0 dBm P1dB

?1.35:1 VSWR

?Single DC power supply

?> 34 years MTBF

?Unconditionally stable

?RoHS Compliant

Product Description

WBPA1016A integrated with WanTcom

Proprietary power amplifier technology, high

Frequency Microelectronics Assembly Technology

High reliability design for optimum high

power, wide bandwidth, high linearity and

Unconditional and stable performance together. use

Single DC voltage operation, the amplifier has

The specified best input and output match

Frequency range for a 50 ohm impedance system.

Amplifier with standard SMA miniature

WP-5 gold plated housing for connector.

Application field

? Mobile Infrastructure

?GPS

?astronomy

national defense

?Security system

?Measurement

?Fixed Wireless

Application Notes:

A. SMA torque wrench selection

Always use a torque wrench with a coupling torque setting of 5 to 6 in-lbs to connect the SMA cable to the amplifier. never use

Tighten with a wrench over 8 in. pound-for-pound to tighten the mating cable to the connector. Otherwise, permanent damage will

Happened to the SMA connector of the amplifier. The 8710-1582 (5 in-lb) is one of Agilent's ideal torque wrench technologies.

B. DC power cord connection

Strip the insulation from the ends of the DC power cables. The length of the peel should be around 0.100 inches to 0.200 inches. twenty four?

Suitable for use with 26 American Wire Gauge wire. Pass the stripped wire around the center pin's DC feed about 3/4 to 1 turn. solder

Twisted wire and center pin together. Clean the solder joints with alcohol with a Q-tip to remove flux and residue.

Do not use a large soldering iron tip above 750 degrees Fahrenheit to solder wires and feed them through pins. may be damaged

Occurs through feed. 0.010 inch size tip with a temperature setting of 750°F for soldering jobs.

Repeat the process to solder the DC return wire to the turret. Higher temperatures and larger soldering iron tips can be used for ground soldering.

C. Install the amplifier

A 1.0" x 1.0" T-shaped film is required between the bottom of the PA and the heatsink for maximum heat dissipation. can't do it

This can cause the PA to overheat and be damaged. Install using three pieces of #4-40 and 9/16"+ screws

Amplifier on a metal base chaser. Flat washers and spring washers are required to prevent screw loosening. Always use an electric screwdriver with the proper torque setting to install screws.

WBPA series broadband power amplifiers are single-ended design, in addition to providing broadband characteristics, it also has excellent gain flatness and ultra-high linearity. IP3 is higher than 50dBm. The frequency bands covered by the amplifier include GPS, DCS, PCS, 3G, MMDS and wireless local area network. Such amplifiers have suitable return loss, gain flatness, high power and efficiency, broadband and unconditional stability (stiffness factor K>1).

[1] Measured at room temperature. Measured at 85 degrees Celsius will increase by 0.3dB

[2] Refers to the temperature difference of the heat dissipation temperature at the highest operating frequency band

Special note: For all amplifier series products, if Unconditional Stable is marked in the product datasheet, k>1, then customers do not need to install isolators in the front and rear stages when using this amplifier product.

is a wireless and networking telecommunications company and a leading supplier of design/manufacture of RF/microwave low noise amplifiers, power amplifiers and subsystems. strong design capabilities,

High-performance products and large-capacity functions are core competencies. Standard products include low noise amplifiers (LNA), highly linear power amplifiers (PA) and subsystems.

In addition to standard products, WanTcom also offers custom products to optimize performance, cost and solution for your specific application. All products are made in the USA.

Offers RF and microwave amplifiers and associated subsystems with ultra-low noise figures of 0.25 dB and ultra-high IP3 of 60 dBm for cellular phone base stations,

RF and microwave communications, MRI imaging, point-to-point communications, and test and measurement.

Provide original equipment manufacturers (OEMs) with high performance and high quality products that meet MIL-STD-202g and MIL-STD-883g.

WHM series company advantage inventory:

WHM02AE

WHM02R

WHM0003AE

WHM0003BE

WHM0005R

WHM0012AE

WHM0012BE

WHM0020AE

WHM0035AE

WHM0105AE

WHM0110AE

WHM0110N

WHM0206AE

WHM0208AE

WHM0210R

WHM0220R

WHM0242AE

WHM0305AE

WHM0510AE

WHM0520-18AE

WHM0525AE

WHM0526AE

WHM0530AE

WHM0545AE

WHM06AE

WHM0814AE

WHM0814BE

WHM0815AE

WHM0913AE

WHM0913R

WHM1014AE

WHM1030AE

WHM1045AE

WHM1115AE

WHM11-2830AE

WHM1318R

WHM1319AE

WHM13-3530A

WHM13-3530AE

WHM14-3020AE

WHM14-3020BE

WHM14-3535AE

WHM1535AE

WHM1722AE

WHM19-1730AE

WHM19-3032AE

WHM2025AE

WHM2026AE

WHM2040AE

WHM2060AE

WHM2227AE

WHM25-1525AE

WHM25-3020AE

WHM2535-12AE

WHM2540AE

WHM3035AE

WHM3043AE

WHM3542AE

WHM5065AE

WHM0002AE

WHM0006AE

WHM0010AE

WHM0013AE

WHM0015AE

WHM005-15AE

WHM0104AE

WHM0205AE

WHM0715AE

WHM0425LE

WHM0913LE

WHM1020LE

WHM1045LE

WHM1045RLE

WHM1216AE

WHM14-2035LE

WHM14-3020LE

WHM14-3035L

WHM14-3035LE

WHM2026L

WHM2535LE

WHM30-2525LE