BYM3635_SI6954ADQ-T1-E3 Introduction

A few days ago, Vishay Intertechnology, Inc. announced that it has expanded its TNPU e3 series of automotive-grade high-precision thin-film flat chip resistors with new devices with a temperature coefficient (TCR) as low as 2 ppm/K, in 0603, 0805 and 1206 form factors.

The power mos used on electric vehicles is a three-dimensional structure. The mos tube we have seen is actually composed of thousands of small mos tubes in parallel. You may think that one or a few bad moss should easily appear in thousands of small mos. In fact, it is not that easy. , the current manufacturing process basically guarantees the high consistency of various parameters of these small units. Low-power mos is a planar structure.

BYM3635_SI6954ADQ-T1-E3

BYP31538

Barrier capacitance: In power semiconductors, when the N-type and P-type semiconductors are combined, the electrons of the N-type semiconductor will partially diffuse into the holes of the P-type semiconductor due to the concentration difference, so they will form on both sides of the junction surface. Space charge area (the electric field formed by the space charge area will resist the diffusion movement, and finally make the diffusion movement reach equilibrium);

Power MOSFETs are generally rarely used in P-channel. Since the mobility of holes is lower than that of electrons, the on-resistance of P-channel transistors is larger than that of N-channel transistors for the same channel size. . According to the two points of the conductive channel and the process of channel formation, MOS tubes can be divided into: P-channel enhancement MOS tubes, P-channel depletion MOS tubes, N-channel enhancement MOS tubes and N-channel depletion MOS tubes . Figure four types of MOSFETs and their graphical symbols.

MOS tube 3306 product features 1. RDS(on)=7mΩ@VGS=10V 2. Lead-free green equipment 3. Low resistance switch to reduce conduction loss 4. High avalanche current.

However, in terms of structure, there is a big difference between them. In order to better understand the mechanism of power MOSFET, we must first recall the mechanism of low-power FET. . The following describes the principle of the MOS transistor with the structure of an N-channel enhancement type low-power MOSFET. Working principle of power MOS tube Power MOS tube is developed from low-power MOS tube.

BYM3635_SI6954ADQ-T1-E3

STM6920

When the UDS increases to a certain value, the drain PN junction breaks down, the leakage current increases rapidly, and the curve turns upward and enters the breakdown region. Power MOSFETs are used in power conversions such as switching power supplies and inverters, and they work in two regions, the cut-off region and the breakdown region. . The full area (UDS>UGS-UT) guarded in the above three areas is the full area, also known as the constant current area or the amplification area. The breakdown region is in the region of considerable drain-source voltage UDS, and the drain current is approximately constant.

NCE3020K NCE3025Q NCE3035K NCE3025G NCE3030K.

. The characteristics of a MOSFET can be characterized by a transfer characteristic curve and a drain output characteristic curve. Figure 3 shows the handling characteristics of a certain FET. The transfer characteristic refers to the relationship curve between the gate voltage UGS and the corresponding drain current ID when the voltage UDS between the drain and the source is at a certain fixed value.

Another technique is to intermittently improve the structure of the MOSFET and use a straight V-groove structure. In order to avoid the problems of too small current-carrying capacity and large on-resistance of MOSFET, two techniques are generally used in high-power MOSFETs. One is to connect millions of low-power MOSFET unit cells in parallel to improve the current-carrying capacity of MOSFET. . FIG. 3 is a cross-sectional view of the structure of a V-channel MOSFET.

BYM3635_SI6954ADQ-T1-E3

The lithium battery of electric vehicles can work normally, largely thanks to the lithium battery protection board.

The functions of the MOS tube in the protection board are: 1. Detect overcharge, 2. Detect over-discharge, 3. Detect over-current during charging, 4. Detect over-current during discharge, 5. Detect over-current during short circuit.

relevant information