Circuit Evaluation Board CN-0414 Circuit Evaluation Board (EVAL-CN0414-ARDZ) CN-0418 Circuit Evaluation Board (EVAL-CN0418-ARDZ) CN-0416 Circuit Evaluation Board (EVAL-CN0416-ARDZ) ADALM-UARTJTAG board Arduino sized development platform (EVAL-ADICUP 3029 ) Design and integration files PLC/DCS Wiki User Guide Schemat...
Read more
feature Serial I/O (Microwire, SPI, and QSPI compatible); 2- or 8-channel differential or single-ended multiplexer; analog input sample/hold function; power-down mode; programmable acquisition time; variable digital output word long and format; no zero-scale or full-scale adjustment required; 0V to 5V analog input range, single 5V supply. Main Specifications Resolution: 12-bit Pl...
Read more
application Common Mode and Differential Mode Filtering Power DC input and output lines communication device computer equipment feature Complies with EU Directive 200295/EC Compatible in lead-free or SnPb reflow environments Small size: 50.8mm x 40.6mm x 12.7mm (2.0". x 1.6". x 0.50") Optimized for high frequency dc-to-dc power module PCB mountable Operating Box Temperatur...
Read more
feature Typical 3Ω switch resistance at 5.0V VCC, VIN = 0V Level shifting facilitates 5V to 3.3V interface Minimum propagation delay through the switch Turn off high-impedance input/output power Zero bounce in overcurrent mode TTL compatible active low control input Control input allows overvoltage illustrate The FSTD3306 is a 2-bit ultra-high-speed CMOS FET with en...
Read more
feature 8 differential analog inputs; 1VPP differential input range; internal/external voltage reference; analog/digital supply: 1.8V; digital input/output supply: 1.8V/3.3V; differential nonlinearity: ±0.4LSB; integral nonlinearity: ± 1.0LSB; Signal-to-Noise Ratio: 59dB, fIN=20MHz; Power Consumption: 733mW; Individual Channel Power Out 257 Leads, 0.8 Ball Pitch, P...
Read more
Speaking of the difficulty of switching power supply, the PCB layout problem is not very difficult, but if you want to lay out a good PCB board, it must be one of the difficulties of switching power supply (the PCB design is not good, it may lead to debugging no matter how the parameters are debugged) The reason is that there are still many factors considered when PCB layout, such as...
Read more
Analysis of PCB Impedance Control Accuracy Initially, the control accuracy requirement of ±10% for PCB was proposed by the application of Direc Rambus type DRAM module (RIMM) with 800MHz frequency signal in the circuit, which is to ensure that the internal circuit of the computer host and switch realizes higher speed operation. Not only computer products equipped with RI...
Read more
feature 1.2 Maximum Load Current; ±2% Output Accuracy Over Temperature; Wide Input Voltage Range: 3.0 V to 20 V; 700 kHz ( ADP2300 ) or 1.4 MHz (ADP2301); Switching Frequency Options; Efficiency Up to 91%; Current Mode Control architecture; output voltage 0.8 V to 0.85 × VIN; automatic PFM/PWM mode switching; precision enable pin with hysteresis; integrate...
Read more
illustrate The FAN7040 is a single bridge tied load (BTL) output amplifier with DC volume control. Designed for use with TVs and monitors, but also for battery-operated portable recorders and radios. This unit is housed in a 20mm wire with a small profile package. Built-in leakage current limiter (MCL). When each amplifier output exceeds 130mA. This level of 130 mA allows sing...
Read more
feature 3-axis sensing; small, low-profile package; 4mm x 4mm x 1.45mm LFCSP; low power consumption: 350 μA typical; single supply operation: 1.8 V to 3.6 V; 10000 g shock survival; excellent temperature stability; single Shaft capacitor bandwidth adjustment; RoHS/WEEE lead-free compliant. application Cost-sensitive, low-power, motion and tilt sensing applications; mobile devices...
Read more
1.0 Main Features Three on-chip phase-locked loops with programmable reference and feedback dividers Four independently programmable mux and postscalers I2 class C 8482 ; bus serial interface Programmable power down for all PLLs and output clock drivers One PLL and two mux/postscaler combinations are modifiable via the SEL_CD input Tri-state outputs for board testing 5V to 3.3...
Read more