Features Ultra-low power consumption: IIN=13mA Regulated Output Voltage: 3.3V±4%, 5V±4% 5V output current: 50mA (VIN³3.0V) 3.3V output current: 40mA (VIN³2.5V) Very low shutdown current required without inductor:
Read more
Function inverting input voltages up to 60 mA output current requires only three small 1µF ceramic capacitors. Input voltage ranges from 1.6 V to 5.5 V, Power save mode (TPS60400) at low output current to improve device quiescent current typical 100µA Integrated Active Schottky Diodes Start Loading Small 5-Pin SOT23 Package Evaluation Module Available TPS60400EVM-...
Read more
Through LS7234 LS7231 is a monolithic, integrated circuit incandescent lamp designed for MOS series brightness control. The output of these ICs controls the brightness of a lamp that controls the firing angle of the triac series lamps. All internal timings are synchronized with the line frequency as a means of built-in phase-locked loop circuitry. The output occurs once per half cycle...
Read more
Features generate single input + and - Up to ±18V output requires only 4 1MF capacitors not inductors 10mA output current minimum operation to 4V not locked 8-pin Minidip applied line driver op amp supplier battery splitter RS-232 Power The LT®1026 is a switched capacitor voltage doubler with inverter in a single chip. Capable of operating from 4V to 10V inputs, it provides ±7V...
Read more
The LTC®2436-1 is a 2-channel differential input micropower 16-bit delay-free DSTM analog-to-digital converter with an integrated oscillator. It provides 0.5LSBINL and 800nV RMS noise independent VREF. The two differential channels, one channel alternate conversion identification is included in the conversion result. It uses delta-sigma technology and provides a single co...
Read more
Features 99.9% voltage conversion efficiency 1.15 V to 5.3 V input voltage range Guaranteed start-up inversion input voltage of 1.15 VIN 700mA quiescent current 25mA output current 500kHz operating frequency ideal for 3.6 V Li-Ion batteries Apply reverse battery protection 5-pin SOT23 package 19W output resistance 0.1% or 0.33µF capacitor The SP6832 device is a CMOS char...
Read more
Features Regulated 5V ± 4% handling charge Pump output current guaranteed at temperature: 20mA (6. 2V.), 30mA (6. 3V) Very low EMI noise without inductance Use small, inexpensive capacitors Logic control leakage current less than 1mA Shutdown supply current Shutdown disconnect load input Available in SO-8 and DIP-8 packages ST619LB is a boost charge pump DC-DC conve...
Read more
The SSI34P3402A device is a high-performance BiCMOS single-chip that contains all read channel ICs to achieve an adaptive function threshold for read channels. Functional blocks include pulse detector adaptive threshold qualifiers, programmable filters, and data synchronization. Raw data rates from 8 to 53 Mbit/s can be commanded through digital programming. The SSI34P3402A a...
Read more
Features Output voltage: 12V±5% Nitrogen supply VOLTAGERANGE: 4.5V to 5.5V Guaranteed output current up to 30mA VERYLOW quiescent current: 100MA LOGICCONTROLLED electronic shutdown: 1mA of capacitor (no inductor required) ST662A Regulated Charge Pump DC-DC Converter. It provides 12V±5% output voltage scheme byte-wide flash memory, and can...
Read more
The TC1121 is a charge pump converter and provides 100mA output current capability. It translates the 2.4V to 5.5V input to the corresponding negative output voltage. As all charge pump converters, the TC1121 does not use an inductor saving cost, size and EMI. The on-board oscillator operates at a typical frequency of 10kHz (V+=5V) when the frequency control input (FC) is connec...
Read more
TC1225/1226/1227 CMOS dual inverting responsible for pump voltage converters, 8-pin MSOP package. The onboard oscillator provides the clock and only four external capacitors are required for a complete circuit implementation. The TC1225 with a switching frequency of 12kHz is 35KHZ and the TC1226 is TC1227125KHZ. These devices provide a negative voltage inversion (“output...
Read more