Describes the reasons for the termination of all analog signals in signal conditioning applications utilizing a single supply where a reference voltage equal to half of the single supply voltage is required. Texas presents a precision instrument whose output voltage is always equal to half the input voltage, the TLE2426 "rail splitter." A unique combination of high performance, micropower op...
Read more
Description/Ordering Information The TLV431 is a low voltage 3 terminal with specified thermal stability, adjustable voltage reference over the applicable industrial and commercial temperature range. The output voltage can be set to any value between VREF (1.24 V) and 6 two external resistors five. These devices operate at low voltages (1.24 V) as referenced by the more widely used ...
Read more
DESCRIPTION The RH1009 is a general purpose 2.5V shunt regulator diode designed to operate over a wide current range while maintaining good stability with time and temperature. The trim terminals allow the use of temperature coefficients for minimization or reference voltage trimming without changing the temperature coefficient. Since it operates as a shunt regulator it can also b...
Read more
DESCRIPTION This monolithic integrated circuit is a completely self-contained precision voltage reference generator with an internal trim of ±1% accuracy. Requires less than 2mA of quiescent current, this device can deliver 10mA of excess total load and line-induced error is less than 0.5%. Additionally this scheme achieves an internally trimmed temperature coefficient for the vol...
Read more
Features • Programmable output voltage to 36 volts • Sink current capability from 1.0mA to 100mA • Typical low dynamic impedance 0.15Ω • Temperature compensated operation at full rated operating temperature • Equivalent to full temperature range with 50ppm/°C (typ) coefficient • Low output noise voltage • Voltage reference tolerance: ±1.0% (beat = 25°C) Application of offic...
Read more
DESCRIPTION The SPX1004 is a 2-terminal high precision bandgap voltage reference that provides a stable 1.2V and 2.5V fixed output voltage with a tolerance of ±4mV for the SPX1004- 1.2 and ±20mV for the SPX1004- 2.5. Design, process and yield cut the chip with a very low temperature accuracy factor of 25 ppm/°C. The SPX1004 can be used as a pin-to-pin replacement ...
Read more
DESCRIPTION The SPX1431 is a three-terminal adjustable shunt regulator providing a highly accurate bandgap reference. The SPX1431 acts as an open loop error amplifier with a 2.5V temperature compensated reference. The SPX1431's thermal stability, wide operating current (150mA) and temperature range (-55°C to 125°C) make it a suitable type of application requiring a...
Read more
DESCRIPTION The SPX2431 is a three-terminal adjustable shunt regulator providing a highly accurate bandgap reference. The SPX2431 acts as an open loop error amplifier with a 2.5V temperature compensated reference. The SPX2431's thermal stability, broad operating current (100mA) and temperature range (0°C to 105°C) make it a suitable low-cost, high-performance solut...
Read more
Features Low output voltage ............................... 1.235V ■Maximum Dynamic Impedance ................................1Ω ■Low temperature coefficient is 30ppm......../°C (typ.) ■Operating Current .................................10μA to 20mA ■Extended temperature range.. -40°C to +85°C ■Initial tolerance.......................... .....1% and 2% ■Pin compatible w...
Read more
2.5 volt reference The NCV1009 is a precision trimmed 2.5 volt ± 5.0 mV shunt Zener diode. Low impedance and wide operating dynamic current range increase its versatility. The close tolerance reference implements on-chip trimming to minimize voltage tolerance and temperature drift. The third terminal allows the reference voltage to be adjusted ±5.0% to calibrate out system errors. In m...
Read more
Explain that the RC0431A is a low-voltage three-terminal adjustable precision voltage reference regulator. It has excellent thermal stability over the standard commercial temperature range. The output voltage can be set to any value between the reference voltage (1.24V) and 12V using two external resistors. The RC0431A operates at lower voltages (1.24V) than conventional shunt regulat...
Read more