The MAX5922A/B/C is a single-port networked power controller with integrated power MOSFETs that operates from a 32 V to 60 V power rail. The device is specially designed for power supply equipment (PSE) for powerover LAN applications and is fully compliant with the IEEE802.3af standard. The MAX5922 provides power device (PD) discovery, classification, current limiti...
Read more
The P-channel features of the MAX869L load switch feature an accurate user-set current limit and low on-resistance. This is designed to protect your power switch shorts and inrush current limiting and prevent the system supply from being pulled low. The input voltage range is 2.7V to 5.5V. The MAX869L features a 2A, 45M half-switch controlling a logic signal. The current limit is...
Read more
The MC33143 is a dual high side switch, solenoid valve control designed for demanding automotive applications but well suited for other environments. Devices can also be used to control small motors and relays as well as solenoids. MC33143 adopts SMARTMOSE technology, CMOS logic circuit, analog circuit, bipolar/MOS and DMOS power output. An internal charge pump is in...
Read more
The AIC1526 is a dual high-side power switch for self-powered and bus-powered Universal Serial Bus (USB) applications. A high-side switch with 110m RDS(ON) MOSFET meets USB voltage drop requirements; maximum transmission line length. Multipurpose open-drain fault flag outputs indicate overcurrent limit, thermal shutdown, or undervoltage lockout for each channel. Typicall...
Read more
Features * Vertical power DMOS switch * Low resistance state 5 V logic compatible input * Overheat protection with hysteresis, self reset * Output overload short circuit protection load current limit; latch - input reset * High supply voltage load protection * Power under voltage lockout * Start overload protection status indication * Diagnostic open load status indication * Very lo...
Read more
The CA3273 is equivalent to a PNP pass transistor power supply IC operating as a current switch in either high-side driver saturation (ON) or cut-off (OFF) mode. The integrated circuit in the CA3273 protects from passing current, excessive input voltage and thermal overload. High-side drivers are used in general purpose vehicles and potentially high-stress applications. If high s...
Read more
The EL7457C is an ultra-high-speed, non-inverting quad CMOS driver. It operates at a clock frequency of up to 40MHz and features a peak drive capability of 2A and a nominal resistance of just 3Ω. The EL7457C is ideal for driving high capacitive loads, such as memory vertical clocks in CCD applications. It is also ideal for ATE pin driving, level shifting and clock driving a...
Read more
The G526 is a dual integrated high-side power switch with independent enable and flag functions, optimized for self-powered and Universal Serial Bus Powered Bus (USB) applications. The G526 meets the following USB requirements: The switch's low on-resistance meets USB voltage drop requirements; fault current is limited to typically 750mA, well below UL25VA safety requir...
Read more
The IPS0151/IPS0151S are fully protected three-terminal smart power MOSFETs with overcurrent, overtemperature, ESD protection and active drain-source clamp.These devices combine a HEXFET® power MOSFET and gate driver. They provide comprehensive protection and the high reliability required in harsh environments. The driver allows short switching times to provide eff...
Read more
VLF302512MT1R0N - SMD inductor SMD inductor (coil) Power cord (winding, magnetic shield) With the VLF302512MT series, the voltage conversion efficiency of DC-DC converters with topclass-sized products is optimized through optimized magnetic materials and configurations. These products are optimal for use as chokes in switches such as power designs for mobile devices that r...
Read more
SMD inductors (coils) for signal lines (multilayer, magnetically shielded) To further streamline various digital devices to maintain a high degree of functionality and to Excel at low power, The parts mounted on the equipment also need to have lower resistance. The MLF1005L type is a new line of inductors that have been developed to meet such requirements: their resistance has dropped b...
Read more