• 2022-09-23 10:23:20

HIP9011 is used to provide a method of detecting early detonations commonly referred to as "hit or hit" internal combustion engines. The integrated circuit is shown in a simplified block diagram. The chip can choose between two sensors for precise monitoring or a "V" motor if desired. Internal control over the SPI bus is fast enough on each transmit cycle. Programmable bandpass filters ...

• 2022-09-23 10:23:20

illustrate Avago's 2.5 Amp integrated gate drive optocoupler mismatch detection and fault status feedback make IGBT VCE fault protection compact, affordable and easy to implement while meeting global safety and regulatory requirements. feature 2.5 Current Max Peak Output Drive IGBT to IC= 150A , VCE=1200V Optical Isolation, Fault Status Feedback SO-16 Package C...

• 2022-09-23 10:23:20

feature SNR = 77.6 dBFS at 70 MHz, 125 MSPS SFDR = 88 dBc at 70 MHz, 125 MSPS; Low Power: 750 mW @ 125 ms/s; 1.8V analog supply operation; 1.8V CMOS or LVDS output supply integer 1 to 8 input clock divider; if sampling frequency up to 300 MHz; -152.8 dBm/Hz small signal input noise, input impedance 200 Ω @ 70 MHz and 125 MSPS; selectable on-chip dithe...

• 2022-09-23 10:23:20

Introduction Electromagnetic compatibility (EMC) is generally defined as the ability of a product to function within its environment without introducing electromagnetic interference. EMC compliance is necessary to bring products to market. Simply put, if a product fails the EMC compliance test for the target market, it cannot be sold. Regulatory agencies around the world impose limits...

• 2022-09-23 10:23:20

Programmable logic controllers (PLCs) and distributed control systems (DCSs) are used to monitor and control intelligent (HART-enabled) and analog field instrumentation in industrial automation applications. The circuit shown in Figure 1 is a simple DCS system consisting of a host, a single node, two 4-channel isolated analog input boards and two 4-channel isolated analog output bo...

• 2022-09-23 10:23:20

feature Low power, small footprint, pin-compatible octal digital-to-analog converter; AD5668 : 16-bit; AD5648: 14-bit; AD5628: 12-bit; 14-lead/16-lead TSSOP, 16-lead LFCSP, and 16-lead WLCSP; on-chip 1.25 V/2.5 V, 5 ppm/°C reference; power supply drops to 400 mA at 5 V and 200 mA at 3 V; 2.7 V to 5.5 V power supply is designed to be monotonic; power-on reset to zero...

• 2022-09-23 10:23:20

feature Bandwidth: 50MHz, 5V; Low Noise: 4.5nV/√Hz; Offset Voltage: 100 μV typical, specified over full common-mode range; Slew rate: 41 V/μs; Rail-to-rail input and output swing; Input Bias Current: 1pa; Single Supply Operation: 2.7 V to 5.5 V; Space-Saving MSOP and SOIC_N Packages. application Optical communications; laser source drivers/controllers; broadba...

• 2022-09-23 10:23:20

illustrate The Versatile Link Series is a complete fiber line for demanding lower cost solutions. The HFBR-0500Z series includes designations for simplicity. This family of components is ideal for solving voltage isolation/insulation issues, immunity to EMI/RFI or data security. The optical link logic compatible receiver simplifies the design and complete specification of each co...

• 2022-09-23 10:23:20

feature Patented sound noise reduction Patented Lamp Aging Compensation 190 VPP output voltage for higher brightness Patented High Efficiency Output Timing Single Cell Li-Ion Compatible 150nA Shutdown Current Wide input voltage range 1.8 to 5.0V Individually adjustable lamps and converters frequency Output voltage regulation Distribution capacity Available in 8-lead MS...

• 2022-09-23 10:23:20

In the design of electronic systems, in order to avoid detours and save time, the requirements of anti-interference should be fully considered and met, and anti-interference remedial measures should be avoided after the design is completed. There are three basic elements that create interference: (1) Interference source refers to the component, device or signal that generates interference, whic...

• 2022-09-23 10:23:20

It must be one of the difficulties of switching power supply to make a good PCB board (the PCB design is not good, it may lead to the situation that no matter how the parameters are debugged, it is not alarmist). The reason is that there are still many factors to consider in PCB layout, such as: electrical performance, process route, safety requirements, EMC impact, etc.; among the f...