• 2022-09-21 17:24:28

Features 1.8 V low RDSON; internal output discharge resistor ( ADP191 ) opens the conversion rate limit (ADP191); low input voltage range: 1.1 V to 3.6636 V; 500 mAh continuous working current; transform can be transformed by controlling logic in the control logic of 1.2V logic; 2 μA (maximum) ground current; ultra -low -off current: lt; 1μA; ultra -small 0.8 mm × 0.8 mm...

• 2022-09-21 17:24:28

ISL6297 is a dual -mode lithium ion battery charger optimization for mobile phone travel chargers. It uses Intersil to apply for a patented dual -mode charging to minimize the technical linear charger generated by the normal heat. ISL6297 can be placed in the stroke connector through the maximization of the calories. ISL6297 is an enhancement to the original ISL6292B. New function...

• 2022-09-21 17:24:28

Features AD5337 8-guided 8-bit DAC AD5338 , AD5338- 1 8 -guide 2 buffer 10 -bit DAC AD5339 8 -guide 2 buffer 12 -bit DAC [123 123 ] -The low-power operation: 3 V 250 mAh, 5 v o'clock 300 mAh -2 line (I2C compatible) serial interface -2.5 V v To 5.5 V power supply -The design of all code is monotonized -The reduced to 80 mAh at 3 V, at 5 V...

• 2022-09-21 17:24:28

Description WM8782 is a high -performance, low -cost stereo sound for ADC designed by recording media applications. The device provides a stereo -sound line level input and two control input pipes (format, IWL), allowing audio interfaces of three industry standard modes. An internal operational amplifier integrates an analog input signal greater than 1VRMS at the front end of...

• 2022-09-21 17:24:28

ISL97656 is a high -frequency, high -efficiency current mode control the non -synchronous boost regulator at the constant PMW switch. It has an internal 4.0A and a 120MΩ low -side MOSFET, which can provide high output current and efficiency of more than 90%. The optional 640kHz1.22MHz switch frequency allows the use of smaller inductance and faster transient response. The e...

• 2022-09-21 17:24:28

CPU manager Features 200MS power-power reset latency low VCC detection and reset assertation-five standard reset threshold voltage-use special programming order adjust the low VCC reset threshold voltage- The reset signal is valid to VCC 1V optional non-easy-to-lose sexual watch dog-0.2, 0.6, 1.4 seconds-Close selection-through software selecting long battery lif...

• 2022-09-21 17:24:28

Features * for a8902Clba Sales and replacement sales * Start the conversion circuit *No sensor switching circuit *Select the external sector data speed table signal *External speed control option *oscillator operates as much as 20 mHz [ 123] *Programmable overcurrent limit *Cross -guidance gain option: 500 mAh/volt or 250 mAh/volt ] *direction control *serial port interf...

• 2022-09-21 17:24:28

CPU manager with 32Kbit SPI EEPROM Function Low VCC detection and resetting assertion-five standard reset threshold voltage-use special programming order to re-program down low VCC reset threshold voltage voltage voltage -The reset signal is valid to VCC 1V battery life is long, low power consumption- lt; 1 Wei'an maximum machine current- lt; 400 Weian maxi...

• 2022-09-21 17:24:28

The ISL6144 ring MOSFET controller and the N -channel power MOSFET of the appropriate size increase the efficiency and availability of the power distribution replacement power O -type diode in large current applications. In the system in multi -power supply, fault tolerance, and redundant power distribution, similar power supply to the load current of various power distribution...

• 2022-09-21 17:24:28

Features *6 V to 45 V input range *5.7V output DC-DC antihypertensive converter *Folding and lack of pressure locking Over current protection (UVLO) *Double 5 V output - Digital 5 v ± 2%, 200 mia -In simulate 5 V, 200 mia [123 ] -The short-circuit protection on the simulation regulator -In simulation-digital regulator output tracking lt; 0.5%, throughout Work...

• 2022-09-21 17:24:28

Use ISL6144Eval1 Z high voltage Oring-MOSFET controller assessment in the power distribution system in multi-power, fault tolerance, redundant power supply, and connect the power supply through various power sharing, so that the load current is used to make the load current Equal plan. Regardless of the solution, an ordinary design practice includes a separate O -type power di...