• 2022-09-23 12:45:58

Features Fixed 60kHz switching frequency 9V to 38V Wide range VDD voltage Current mode control Auxiliary undervoltage lockout with hysteresis W-8, 13 W for DIP-8 – Europe (85-265 VAC) 5 W for SO-8, 8 W for DIP-8 Description The Viper12A combines a dedicated current-mode PWM controller and a high-voltage power MOSFET on the same silicon die. Typical applica...

• 2022-09-23 12:45:58

The DS1721 2-Wire digital thermometer and temperature monitor provides a 12-bit temperature reading which indicates the temperature of the device. Thermostat settings and temperature readings are transmitted to/from the DS1721 via a simple 2-wire serial interface. No additional components are required; the device is a true "temperature-to-digital" converter. The DS1721 has three address...

• 2022-09-23 12:45:58

The BQ2083-V1P3 SBS standard fuel gauge IC is installed and maintained in a battery pack or system to accurately record the available charge in Li-ion or Li-polymer cells. The bq2083-V1P3 monitors key parameters of the battery pack such as capacity and reports the information communication bus provided to the system host controller via the serial port. It is designed to maximize fu...

• 2022-09-23 12:45:58

Integrated Depop Circuit with PC Power Supply High Power – 2 W/ch at 5 V, Input 3Ω Load – 800 mW/ch at 3 V, Fully Specified for 3Ω Load, Ultra Low Distortion – 2 W and 3Ω Load Bridged Load (BTL ) or 0.05% THD+N in single-ended (SE) mode, Stereo Input Multiplexer Surface Mount Power Pack 24-pin TSSOP PowerPad Shutdown Co Control...IDD des...

• 2022-09-23 12:45:13

Inside the CAT25640VI-GT3 is an EEPROM serial 64-Kb SPI device organized as 8Kx8 bits. This has a 64-byte page write buffer and supports the Serial Peripheral Interface (SPI) protocol. The device is enabled through the Chip Select (CS) input. Also required bus signals are the clock input (SCK), data input (SI) and data output (SO) lines. The HOLD input c...

• 2022-09-23 12:45:13

The FAN5234 PWM controller provides high efficiency and adjustable output from 0.9V to 5.5V power required for I/Os, chipsets, memory banks, or peripherals in high-performance laptops, PDAs, and Internet appliances. Synchronized trim and hysteretic operation contributes to high efficiency loads over a wide range at light loads. Hysteresis mode of operation can be disabled if all l...

• 2022-09-23 12:45:13

Features DESCRIPTION The TPS54160A device is a 60-V, 1.5-A, step-down 1.3.5 V to 60 V input voltage range regulator with an integrated high-side MOSFET. 200-MΩ high-side MOSFET current-mode control provides simple external high efficiency at light loads, pulse compensation and flexible component selection. Skip ECO Mode™ Low Ripple Pulse Skip Mode redu...

• 2022-09-23 12:45:13

The DS1339 serial real-time clock (RTC) is a low-power clock/calendar chip with two programmable calendar alarms and one programmable square wave output. Address and data are transferred serially over the I2C bus. The clock/calendar can provide seconds, minutes, hours, day, month, and year information. For months with fewer than 31 days, adjustments are made automatically to the last da...

• 2022-09-23 12:45:13

The AD8009AR is an ultra-high-speed current feedback amplifier with an impressive 5,500 V/µs slew rate resulting in a rise time of 545 ps, making it ideal as a pulse amplifier. The high slew rate reduces the effects of slew rate limitations resulting in the large signal bandwidth of 440 MHz required for high-resolution video graphics systems. Maintain signal quality over wide bandwidth,...

• 2022-09-23 12:45:13

Products highlight lowest cost, low power switching solutions Lower cost than RCC, discrete PWM and other integrated/hybrid solutions Cost effective replacement of bulky linear adapters Lowest component count Simple on/off control – No Loop Compensation No Bias Winding – Simpler, Lower Cost Transformer Allows SIMs Up to 2 W from Universal Input or up to 4 W from 115...

• 2022-09-23 12:45:13

The CMOS BQ2201SN SRAM non-volatile controller unit provides all the functions necessary to convert standard CMOS SRAM into non-volatile read/write memory. Precision comparators monitor the 5V VCC input for out-of-tolerance conditions. When out of tolerance is detected, the conditional chip enable output is forced inactive to write protect any standard CMOS SRAM....