• 2022-09-23 10:04:02

feature Signal-to-Noise Ratio = 60.6dbc (61.6dbfs) to 70mhz, 150ms/sec; SFDR = 81dBc to 70MHz, 150ms/sec; Low Power: 825mW at 150MSPS; 1.8V Analog Supply Operation; 1.8V To 3.3 V CMOS output power supply or 1.8 V LVDS power supply; integer 1 to 8 input clock divider; IF (IF) sampling frequency up to 450 MHz; internal analog-to-digital converter (ADC) volta...

• 2022-09-23 10:04:02

Signal monitor The Signal Monitor block provides additional information about the signal being digitized by the ADC. The signal monitor calculates the rms input amplitude, peak amplitude, and/or the number of samples whose amplitude exceeds a certain threshold. At the same time, these functions can be used to gain insight into signal characteristics and estimate the peak/average ratio of ...

• 2022-09-23 10:04:02

feature High Speed: Typical 150 Mbps (S-Series) High temperature: -40°C to +125°C (T series and VE series) Very high isolation: 6 kVRMS reinforced isolation (VE series) High operating voltage: 1 kVRMS per VDE V 0884-10 (VE series) 50 kV/μs typical; 30 kV/μs minimum common-mode transient immunity No carrier or clock for low EMI emissions and susceptibility 1....

• 2022-09-23 10:04:02

This family of fully featured hot-swap power controllers targets applications in the +2.5V to +12V range. The ISL6115 for +12V control, the ISL6116 for +5V, and the ISL6117 for +3.3V and ISL6120 for +2.5V control are applied. Each has a hardwired undervoltage (UV) monitoring and reporting threshold level approximately 80% of the aforementioned voltage. The ISL6115 has an...

• 2022-09-23 10:02:16

Features 3.5 to 28 V input voltage range Adjustable output voltage down to 0.8 V Integrated 80-mΩ high-side MOSFET supports up to 3-A continuous output current Light Load High Efficiency™ with Pulse Skip Eco Mode Fixed 570 kHz switching frequency Typical 1-µA Shutdown Quiescent Current Adjustable slow start to limit inrush current Programmable UVLO Threshold O...

• 2022-09-23 10:02:16

feature 3 Instructions Low power consumption: 1.4ma/ch typical The TL08xx JFET input op amp family is Wide Common Mode Differential Voltage Designed to provide a wider selection of op amps than any previously developed family of op amps. scope Each JFET input op amp Low input bias current: typical 30pa using well-matched high-voltage JFETs and Low Input Bias Current: 5...

• 2022-09-23 10:02:16

feature Offset voltage: 400 microvolts typical; low offset voltage drift: 6 microvolts/degree Celsius max ( AD8692 /AD8694); very low input bias current: 1pa max; low noise: 8 nV/√Hz; low distortion : 0.0006%; Broadband: 10 MHz; Unity Gain Stable; Single Supply Operation: 2.7 V to 6 V; Suitable for Automotive Applications. application Photodiode amplification; battery power...

• 2022-09-23 10:02:16

feature Low power quad 16-bit DAC; 14-lead TSSOP on-chip 1.25 V/2.5 V, 5 ppm/°C reference; power down to 400 mA at 5 V and 200 mA at 3 V; 2.7 V to 5.5 V supply; guaranteed monotonicity by design; power-on reset to zero-scale or mid-scale; 3 power-down functions; hardware LDAC with LDAC override; CLR function to programmable code; SDO daisy-chain option; rail-to-rai...

• 2022-09-23 10:02:16

The ISL6740 , ISL6741 series of adjustable frequency, low power, pulse width modulation (PWM) voltage mode (ISL6740) current mode (ISL6741) controllers are designed for full-bridge half-bridge power conversion applications ranging from bridging and push-pull configurations. These controllers provide a very flexible oscillator with precise control of frequency, duty cycle and dead ...

• 2022-09-23 10:02:16

feature High-resolution analog-to-digital converter (ADC); 24-bit no missing codes; ±0.0025% nonlinearity; optimized for fast channel switching; 18-bit pp resolution at 500Hz (21-bit effective) 16-bit pp resolution at 2 kHz ( 19-bit valid); 14-bit pp resolution at 15 kHz (18-bit valid); on-chip per-channel system calibration; 4 single-ended analog inputs; input ranges +5 V, ±5 V, +10 V...

• 2022-09-23 10:02:16

The ISL59830A is a revolutionary device that allows single-supply operation of video amplifiers. The device runs off a single 3.3V supply and generates the desired negative internal voltage. This enables DC precision coupling to play video on a 75Ω double-ended circuit. Because the buffer has an integrated 6dB gain, the only external components require a 75Ω termination resistor and ...