The ISL6545 enables the realization of a complete DC/DC buck control protection scheme for converter topologies driving N-channel mosfets in synchronous bucks. Because it can work with 5V or 12V supplies, one IC can be used in the system. The ISL6545 integrates control, gate driver, output regulation, monitoring and protection functions into an 8Ld SOIC or 10 Ld DFN pack...
Read more
Feature description Designed to protect submicron 3-V or 5-V, the SN65220 device is dual-supply, the SN65240 and The circuits from the noise transient SN75240 device are four unidirectional transient voltage suppressors (TVS). these devices Port ESD Protection Exceeds: Provides electrical noise transient protection for -15kV Human Body Model Universal Serial Bus (USB...
Read more
feature illustrate Input Voltage Range: 4.75 V to 5.25 V TPS51100 Product Specifications, Documentation and Sourcing Information terminal conditioner. The device is designed for low cost and low external components. The 3-A sink/source termination conditioner includes a counting system at the expense of space. Sag compensation only requires 20μF ceramic output capacitor TPS51...
Read more
main feature 350MHz high-performance Blackfin processor core; two 16-bit macs, two 40-bit alus, one 40-bit shifter, four 8-bit video alus and two 40-bit accumulators; RISC-like register and instruction model; programming and compiler friendly support; advanced debug, trace and performance monitoring; 1.0 V–1.6 V core VDD with dynamic power management; 3.3 V input/output; 260-ball PB...
Read more
The ICL7665S Ultra CMOS Micropower Over/Under Voltage Detector contains two separate low power programmable voltage detectors. Typically 3µA operating current is required, the device is designed for applications requiring high or low voltage warnings, programmable trip points, or fault monitoring and correction. Trigger point and hysteresis for both voltage detectors through ext...
Read more
Features and Benefits ▪ N-channel MOSFET full bridge high current gate driver ▪ High side or low side PWM switch ▪ Charge pump operating at low supply voltage ▪ 100% PWM top-up charge pump ▪ Cross-conduction protection with adjustable dead time ▪ 5.5 to 50 V supply voltage range ▪ Integrated 5V regulator ▪ Diagnostic output ▪ Low current sleep mode illustrate The ...
Read more
The ISL6742 is a high performance double-ended pulse width modulation with advanced synchronous rectifier control and current limiting features. It is suitable for current and voltage mode control methods. The ISL6742 includes Synchronous Rectifier (SR) control. The supplemental output can be relative to the main output using an external control voltage. Its advanced current sensing...
Read more
feature Low power consumption Wide Common Mode Differential Voltage scope Low input bias and bias current Output short circuit protection Low Total Harmonic Distortion: 0.003% typical low noise At f=1kHz, Vn=18nV/√Hz typical illustrate The TL07xx JFET input op amp family is designed to provide a wider selection than any previously developed op amp family. Each JFET-in...
Read more
feature The TL431 and TL432 devices are three terminal 25°C reference voltage adjustable shunt regulators with specified thermal – suitable for automotive, commercial and –1% (Class A) military temperature range. The output voltage can be set to any value between Vref – 2% (standard grade) (approximately 2.5 V) and 36 V with two external resistors. These adjustable output voltage:...
Read more
General Instructions The AAT4650 smart switch is a single-channel PC card (PCMCIA) power switch. It is used to select between two different voltage inputs, each between 2.7V and 5.5V. An internal switch powers the circuit from the higher input voltage. The device's output, V, is controlled for slew rate and current limit, in accordance with PC Card specifications. The c...
Read more
These Intersil RS-485 /RS-422 devices are ESD protected, BiCMOS 5V power supply, single transceiver, and meet the RS-485 and RS-422 balanced communication standards. Each driver output/receiver input is protected from ±15kV ESD strikes without latch-up. Unlike competing devices, this Intersil series is specified for a 10% tolerance supply (4.5V to 5.5V). The ISL848...
Read more