• 2022-09-23 11:57:15

The EL5166 and EL5167 are current-feedback amplifiers with an extremely high bandwidth of 1.4GHz at a gain of +1 and a high bandwidth of 800MHz at a gain of +2. This makes these amplifiers ideal for today's high-speed video and surveillance applications, as well as some RF and IF frequency designs. The EL5166 and EL5167 amplifiers have a supply current of only 8.5mA and can...

• 2022-09-23 11:57:15

Reset control, watchdog timer and supply voltage monitoring. This combination reduces system cost, reduces board space requirements, and improves reliability. Applying power to the device activates a power-on reset. Circuits that keep reset/reset active for a period of time. This allows the power supply and oscillator to stabilize before the processor executes code. The watchdog timer provid...

• 2022-09-23 11:57:15

The CDCE906 is one of the smallest and most powerful clock synthesizer/jitter cleaner products. Programmable Output Switch Matrix [6x6] Despite its small physical size, the CDCE906 includes a 7-bit postscaler per output. Flexible . It has the ability to generate almost differential input clock or single crystal. The reduced system EMISMBus data interface controller. To achi...

• 2022-09-23 11:57:15

feature 8226 ; optional watchdog timer Low VCC detection and reset assertion - Four standard reset threshold voltages - Adjust low VCC reset threshold voltage using special programming sequence - Reset signal valid to VCC=1V Low power CMOS -

• 2022-09-23 11:57:15

The AD7714 is a complete analog front-end measurement application device for low frequencies. The device accepts a low level signal directly from the transducer and outputs a serial digital word. It uses sigma-delta conversion technology to achieve up to 24 bits without loss of code performance. The application input signal is based on a proprietary programmable gain front end analog modulat...

• 2022-09-23 11:57:15

In the functional block diagram of the HIP4020 , the four switches and loads are arranged in an H configuration so that voltages driven from terminals OUTA and OUTB can be cross-switched to change the direction of current flow in the load. This is often referred to as four-quadrant load control. As shown in the block diagram, when switches Q1 and Q4 are conducting or in the ON s...

• 2022-09-23 11:57:15

While the transition of electric and hybrid electric vehicles (EVs) from standard metal-oxide-semiconductor field-effect transistors (MOSFETs) as power control devices to FETs based on silicon carbide (SiC) substrates and process technology represents an increase in EV efficiency and An important step in overall system-level characterization. However, SiC devices require a new ...

• 2022-09-23 11:57:15

The DIT4096 is a complete digital audio transmitter suitable for professional and consumer audio applications. SAM-coupling rates up to 96kHz are supported. The DIT4096 COM ply meets the requirements for AES-3, IEC-60958, and EIAJCP1201 interface standards. Figures 1 and 2 show the DIT4096 block diagram when used in software and hardware control modes. The MODE ...

• 2022-09-23 11:57:15

BD2041AFJ and BD2051AFJ are single-channel high-side switching ICs with overcurrent protection for Universal Serial Bus (USB power lines. These ICs feature low on-resistance N-channel power MOSFETs with low supply current, built-in overcurrent protection circuitry, thermal shutdown circuit breaker, lower voltage lockout and soft-start circuit. Typical Application Cir...

• 2022-09-23 11:57:15

Introduction to Conversion Socket Specifications Conversion sockets are products that allow a header board (for next-generation circuit simulators or circuit debuggers) or device adapters (for MPLAB ICE 2000 circuit simulators) to interface with a socket on a target application . Typically, a header board or device adapter has a connector that matches the development cycle device for...

• 2022-09-23 11:57:15

The EL4340 and EL4342 are fixed unity gain amplifier multiplexers with high slew rate and excellent bandwidth for video switching. These devices have high impedance output states (HIZ) so that the outputs of multiple devices are connected together. A power-down mode (ENABLE) includes shutting down non-essential circuits for power-sensitive applications. The enable pin, when pulled...