The DF1706 's system clock can be supplied via an external clock signal at XTI (pin 6), or via the on-chip crystal oscillator. The system clock rate must be running at 128FS, 192fS, 256fS, 384fS, 512fS or 768fS, where fS is the audio sample rate. When a 128fS or 192fS system clock is applied to the DF1706, the oversampling ratio (OSR) of the DF1706 digital filter shoul...
Read more
Conversion time 10 to 10 bit resolution ADC programmable power down mode I'm sorry. 1.2.7 V dc to 5.5 V dc wide range single supply operation 0 V to VCC built-in analog multiplexer, 8 analog input channels TMS320 DSP and microprocessor SPI and QSPI compatible serial interface in self-test mode, Extended Sampling Hardware I/O Clock Phase Adjust Input Programmab...
Read more
The EL5152 , EL5153 , EL5252 , EL5455 are 270MHz, -3dB bandwidth, voltage mode feedback amplifiers,
Read more
BQ24086 , BQ24088 , BQ24085 are all BQ2408x series are highly integrated Li-Ion batteries, ideal for low dropout designs of single-cell LiLi-Pol linear chargers for space-constrained applications Space-constrained Ion or Li in portable applications -Pol package. The BQ2408x series provides a current and constant voltage. Charge termination ±0.5% voltage regulation accuracy ba...
Read more
Features Operating Input Voltage 10 V to 40 V Programmable Fixed Frequency up to 100 kHz to 1 MHz Voltage Mode Controller Internal Gate Drive Output for High Side and Synchronous N-Channel MOSFETs 16-pin PowerPad Package (JC=2c/w) Thermal Shutdown External Synchronous Programmable Short Circuit Protection Programmable Closed-Loop Soft-Start Applicat...
Read more
The CY2291 is the third generation of the clock generator family. The CY2291 is upwardly compatible with the industry standard ICD2023 and ICD2028 by providing a continuation of its traditional high level of customizable features to suit different clock synchronization systems. All components provide the PC with a set of highly configurable shutdown functions for motherboard applica...
Read more
HIN232 - HIN241 series RS-232 transmitter/receiver interface circuits meet all E1ARS-232E and V.28 specifications, and are especially suitable for applications where ± 12V is not available. They require a single +5V power supply (except the HIN239) and feature an onboard charge pump voltage converter which generates +10V and 5V power and -10V power. This series of devices ...
Read more
Both CAN and 485 are commonly used field buses in industrial communication. All engineers must be very familiar with the bus isolation scheme, but they may encounter the situation that the bus adopts the isolation scheme and still has abnormal communication. This article will take you to discuss the bus isolation scheme. How to ground? 1. Preface In order to ensure the communication stabi...
Read more
The DAC8830 and DAC8831 are single-channel, 16-bit, serial input, voltage output digital-to-analog converters (DACs) that operate from a single 3V to 5V supply. These converters provide excellent linearity (1LSBINL), low glitch, low noise and fast settling (1.0μS1/2LSB full-scale output) over a specified temperature range of -40°C to +85°C. The output is buffered, ther...
Read more
The ADC0808 , ADC0809 data acquisition component is a monolithic CMOS device with 8-bit analog-to-analog scaling voltage reference microprocessor compatible control logic. 8-bit conversion technology. The converter features a high 8-channel multiplexer and address logic impedance chopper-stabilized comparator, 256R asks any one of the 8 single-ended analog signals. The device require...
Read more
Application IF Amplifier VHF/UHF Transmission Wireless Infrastructure Cable/Satellite/MOCA Product feature functional block diagram 50 ohm Cascadable Gain Blocks 50– 1000 MHz 19.5dB gain at 200MHz +20.5 dBm p1db at 200 MHz +43.5 dBm output IP3, 200 MHz +60 dBm output IP2 at 200 MHz Single +5 V supply, 95 mA current 1000 V electrostatic discharge, class...
Read more